HC2910 (Shandong Broadnet)
Board
:USB_BOOT: See below
bootargs
baudrate=115200
bootargs=console=ttyAMA0,115200 blkdevparts=mmcblk0:2M(fastboot),2M(bootargs),2M(bootargsbak),10M(recovery),10M(recoverybak),2M(properties),2M(markparam),2M(baseparam),2M(pqparam),20M(logo),40M(fastplay),20M(kernel),2M(misc),50M(private),2M(tpl),100M(factory),600M(otapackage),100M(cache),800M(system),-(userdata) quiet
bootargs_1G=mem=1G mmz=ddr,0,0,44M
bootargs_2G=mem=2G mmz=ddr,0,0,44M
bootargs_3840M=mem=1G mmz=ddr,0,0,44M
bootargs_512M=mem=512M mmz=ddr,0,0,44M
bootargs_768M=mem=768M mmz=ddr,0,0,44M
bootcmd=mmc read 0 0x1FFBFC0 0x2F000 0x5000; bootm 0x1FFBFC0
bootdelay=0
bootfile="uImage"
gmac_debug=0
ipaddr=192.168.1.10
netmask=255.255.255.0
phy_addr=2,1
phy_intf=mii,rgmii
serverip=192.168.1.1
stderr=serial
stdin=serial
stdout=serial
use_mdio=0,1
verify=n
Flash layout
Name |
Offset |
Size |
Description |
|---|---|---|---|
fastboot |
0M |
2M |
|
bootargs |
2M |
2M |
U-Boot env file, sector size: |
bootargsbak |
4M |
2M |
bootargs backup |
recovery |
5M |
10M |
U-Boot legacy uImage |
recoverybak |
5M |
10M |
recovery backup |
properties |
5M |
2M |
|
markparam |
5M |
2M |
? |
baseparam |
22M |
2M |
|
pqparam |
26M |
2M |
Video Post Processing parameters |
logo |
30M |
20M |
|
fastplay |
34M |
40M |
Fastboot DRM parameters (optional) |
kernel |
82M |
20M |
Android bootimg |
misc |
50M |
2M |
empty |
private |
82M |
50M |
ext3/4, Android |
tpl |
82M |
1M |
squashfs, Android
|
factory |
58M |
100M |
U-Boot legacy uImage |
otapackage |
94M |
600M |
ext3/4, Android A single |
cache |
442M |
100M |
ext3/4, Android |
system |
782M |
800M |
ext3/4, Android |
userdata |
1302M |
ext3/4, Android |
Fastboot
fastboot# getinfo ddrfree
DDR free region baseaddr:0x1000000 size:0x3F000000
fastboot# help
? - alias for 'help'
base - print or set address offset
bootm - boot application image from memory
bootp - boot image via network using BOOTP/TFTP protocol
clear_bootf- clear Hibernate!! bootflag
cmp - memory compare
cp - memory copy
crc32 - checksum calculation
ddr - ddr training function
fatinfo - print information about filesystem
fatload - load binary file from a dos filesystem
fatls - list files in a directory (default /)
fdt - flattened device tree utility commands
getinfo - print hardware information
go - start application at address 'addr'
help - print command description/usage
hibernate- Hibernate!! boot
ir - IR command:
loadb - load binary file over serial line (kermit mode)
loady - load binary file over serial line (ymodem mode)
loop - infinite loop on address range
md - memory display
mii - MII utility commands
mm - memory modify (auto-incrementing address)
mmc - MMC sub system
mmcinfo - mmcinfo <dev num>-- display MMC info
mtest - simple RAM read/write test
mw - memory write (fill)
nand - NAND sub-system
nboot - boot from NAND device
nm - memory modify (constant address)
otp_burntoecurechipset- Burn to secure chipset, please be careful !!!
otp_getcustomerkey- otp_getcustomerkey
otp_getstbprivdata- otp_getstbprivdata
otp_gettrustzonestat- Get TEE status
otp_setstbprivdata- StbPrivData
otp_settrustzone- Set TEE enable
otpreadall- read otp ,for example otpreadall
otpwrite- write otp ,for example otpwrite adddress value
ping - send ICMP ECHO_REQUEST to network host
printenv- print environment variables
rarpboot- boot image via network using RARP/TFTP protocol
reset - Perform RESET of the CPU
saveenv - save environment variables to persistent storage
setenv - set environment variables
tftp - tftp - download or upload image via network using TFTP protocol
unzip - unzip a memory region
uploadx - upload binary file over serial line (xmodem mode)
usb - USB sub-system
usbboot - boot from USB device
version - print monitor version
Boot log
Bootrom start
Boot Media: eMMC (Default Speed)
Decrypt auxiliary code ...OK
lsadc voltage min: 00000100, max: 00000101, aver: 00000100, index: 00000004
Enter boot auxiliary code
Build: Oct 10 2018 - 11:10:02
Reg Time: 2019/03/06 18:59:48
Reg Name: hi3798m2hdmd_hi3798mv200h_DDR3-1866_1GB_16bitx2_4layers_A0825.reg
Set cpu freq
Boot auxiliary code success
Bootrom success
System startup
Relocate Boot
Jump to C code
Fastboot 3.3.0 (proj-sdL-jngdzx_cwsz_121374@join-r730-00) (Dec 09 2021 - 14:25:31)
Fastboot: Version 3.3.0
Build Date: Dec 9 2021, 14:26:50
CPU: Hi3798Mv200H
Boot Media: eMMC
DDR Size: 1GB
LOGO Flag:3d34a8d2
Found flash memory controller hifmc100.
no found nand device.
MMC/SD controller initialization.
scan edges:2 p2f:6 f2p:8
mix set temp-phase 3
scan elemnts: startp:128 endp:122
Tuning SampleClock. mix set phase:[03/07] ele:[13/16]
MMC/SD Card:
MID: 0x15
Read Block: 512 Bytes
Write Block: 512 Bytes
Chip Size: 7456M Bytes (High Capacity)
Name: "8GTF4R"
Chip Type: MMC
Version: 5.1
Speed: 100000000Hz
Mode: HS400
Voltage: 1.8V
Bus Width: 8bit
Boot Addr: 0 Bytes
Net: up
Boot Env on eMMC
Env Offset: 0x00200000
Env Size: 0x00010000
Env Range: 0x00010000
SDK Version: gitServer_v2018121410
Normal logo
bootargs RECOVERY_CHECK_MODE=<NULL>
start check ir booting:
0xeb14ef10||0x0, BOOTING_FACTORY_ALONE_KEYCODE(4)
0xbc43ef10||0xe916ef10, BOOTING_FACTORY_FN_KEYCODE(3)
0xbc43fe01||0x0, BOOTING_FACTORY_ALONE_KEYCODE(4)
0x7d82dd22||0x7e81dd22, BOOTING_RECOVERY_SHOW_UI(1)
0x35cadd22||0x0, BOOTING_RECOVERY_NOT_SHOW_UI(2)
0xf20def10||0x0, BOOTING_RECOVERY_NOT_SHOW_UI(2)
0xf20d1920||0x0, BOOTING_RECOVERY_NOT_SHOW_UI(2)
0x35cafd01||0x0, BOOTING_RECOVERY_NOT_SHOW_UI(2)
0x35caef11||0x0, BOOTING_RECOVERY_NOT_SHOW_UI(2)
0xfc032c40||0x0, BOOTING_RECOVERY_NOT_SHOW_UI(2)
0xff007748||0x0, BOOTING_RECOVERY_NOT_SHOW_UI(2)
[Recovery] Wate Times: 302ms(906ms)
[Recovery] Wate Times: 604ms(906ms)
[Recovery] Wate Times: 906ms(906ms)
serialno:XXXXXXXXXXXXXXXX
properties mac match step1.
properties mac=XX:XX:XX:XX:XX:XX.
mac:XX:XX:XX:XX:XX:XX
Reserve Memory
Start Addr: 0x3FFFE000
Bound Addr: 0x8D8F000
Free Addr: 0x3EF24000
Alloc Block: Addr Size
0x3FBFD000 0x400000
0x3F8FC000 0x300000
0x3F8F9000 0x2000
0x3F8F7000 0x1000
0x3F8F4000 0x2000
0x3F8F2000 0x1000
0x3F8EF000 0x2000
0x3F79C000 0x152000
0x3EFB1000 0x7EA000
0x3EFAF000 0x1000
0x3EFA5000 0x9000
0x3EF24000 0x80000
Press Ctrl+C to stop autoboot
MMC read: dev # 0, block # 192512, count 20480 ... 20480 blocks read: OK
175762560 Bytes/s
Found Initrd at 0x04000000 (Size 352002 Bytes), align at 16384 Bytes
## Booting kernel from Legacy Image at 01ffffc0 ...
Image Name: Linux-3.18.24_hi3798mv310
Image Type: ARM Linux Kernel Image (uncompressed)
Data Size: 8694300 Bytes = 8.3 MiB
Load Address: 02000000
Entry Point: 02000000
XIP Kernel Image ... OK
OK
ATAGS [0x00000100 - 0x00000500], 1024Bytes
Starting kernel ...
Uncompressing Linux... done, booting the kernel.
mdio_bus f9840000.hieth1: /soc/hieth1@f9840000/hieth_phy@1 PHY address 255 is too large
hi_eth: no dev probed!
init: /init.bigfish.rc: 59: invalid command 'getprop'
init: /init.bigfish.rc: 118: invalid option 'sdcard_r'
init: /init.bigfish.rc: 223: invalid option '//add'
init: /init.bigfish.rc: 374: invalid command '//insmod'
init: /dev/hw_random not found
init: cannot open '/initlogo.rle'
init: /dev/hw_random not found
healthd: wakealarm_init: timerfd_create failed
init: cannot find '/system/bin/rild', disabling 'ril-daemon'
init: cannot find '/system/bin/dbus-daemon', disabling 'dbus'
init: cannot find '/system/etc/install-recovery.sh', disabling 'flash_recovery'
init: cannot find '/system/bin/teecd', disabling 'teecd'
init: cannot find '/system/bin/basicService', disabling 'basicService'
init: cannot find '/system/bin/startsoftdetector.sh', disabling 'softdetector'
init: cannot find '/system/bin/xiriservice_All', disabling 'xiriservice'
init: cannot find '/system/bin/frontPanel', disabling 'frontPanel'
init: cannot find '/system/bin/mtkbt', disabling 'blueangel'
init: cannot find '/system/bin/dtvserver', disabling 'dtvserver'
init: cannot find '/system/bin/usb-driver', disabling 'usb-driver'
init: property 'sys.powerctl' doesn't exist while expanding '${sys.powerctl}'
init: powerctl: cannot expand '${sys.powerctl}'
init: property 'sys.sysctl.extra_free_kbytes' doesn't exist while expanding '${sys.sysctl.extra_free_kbytes}'
init: cannot expand '${sys.sysctl.extra_free_kbytes}' while writing to '/proc/sys/vm/extra_free_kbytes'
healthd: No charger supplies found
root@Hi3798MV200H:/ # init: sys_prop: permission denied uid:1000 name:ro.config.gfx2d_compose
init: untracked pid 1116 exited